Engineering:Caliber

From HandWiki
From left: .50 BMG, .300 Win Mag, .308 Winchester, 7.62×39mm, 5.56×45mm NATO, .22LR (Note that the 5.56×45mm NATO round and the .22LR round have the same diameter bullets but very different cartridges)
A .45 ACP hollowpoint (Federal HST) with two .22 LR cartridges for comparison
Side on view of Sellier & Bellot .45-cal ACP cartridge with a metric ruler for scale

In guns, particularly firearms, caliber or calibre is the approximate internal diameter of the gun barrel, or the diameter of the projectile it shoots.[1] It is measured in hundredths or thousandths of an inch or in millimetres.[2] For example, a ".45 caliber" firearm has a barrel diameter of roughly 0.45 inches (11 mm). Barrel diameters can also be expressed using metric dimensions. For example, a "9mm pistol" has a barrel diameter of about 9 millimetres (it is rare for the actual barrel diameter to precisely match the designation however, and the bullet itself is yet another dimension). When the barrel diameter is given in inches, the abbreviation "cal" (for "caliber") can be used. For example, a small-bore rifle with a diameter of 0.22 inches (5.6 mm) can be referred to as a ".22" or ".22 cal"; however, the decimal point is generally dropped when spoken, making it a "twenty-two" or a "two-two caliber". A ".45 caliber" would be a "forty-five", or "four-five caliber", etc.

In a rifled barrel, the distance is measured between opposing lands or grooves; groove measurements are common in cartridge designations originating in the United States , while land measurements are more common elsewhere in the world. Good performance requires a bullet to closely match the groove diameter of a barrel to ensure a good gas seal and hence maximal bullet propulsion.

While modern firearms are generally referred to by the name of the cartridge the gun is chambered for, they are still categorized together based on bore diameter. For example, a firearm might be described as a "30 caliber rifle", which could be any of a wide range of cartridges using a roughly 0.30 inches (7.6 mm) projectile; or a "22 rimfire", referring to any rimfire firearms firing cartridges with a .22 caliber projectile.

Firearm calibers outside the range of .17–.50 inches (4.3–12.7 mm) exist, but are rarely encountered. Wildcat cartridges, for example, can be found in .10, .12, and .14 cal (2.5, 3.0, and 3.6 mm), typically used for short-range varmint hunting[citation needed], where the high-velocity, lightweight bullets provide devastating terminal ballistics with little risk of ricochet. Larger calibers, such as .577, .585, .600, and .700 (14.7, 14.9, 15.2, 17.8 mm) are generally found in proprietary cartridges chambered in express rifles or similar guns intended for use on dangerous game.[3] The .950 JDJ is the only known cartridge beyond 70 caliber used in a rifle.

Referring to artillery, "caliber" is used to describe the barrel length as multiples of the bore diameter. A "5-inch 50 calibre" gun has a bore diameter of 5 in (12.7 cm) and a barrel length of 50 times 5 in = 250 in (6.35 m). The main guns of USS Missouri, an Iowa-class battleship, are 16" 50 caliber.

In shotguns, each gauge of shotgun has a set caliber. For example, a 12 gauge shotgun has a caliber of 18.53 mm or .729 inches.

Cartridge naming conventions

Makers of early cartridge arms had to invent methods of naming cartridges since no established convention existed then.[4] One of the early established cartridge arms was the Spencer repeating rifle, which Union forces used in the American Civil War. It was named based on the chamber dimensions, rather than the bore diameter, with the earliest cartridge called the "No. 56 cartridge", indicating a chamber diameter of .56 in; the bore diameter varied considerably, from .52 to .54 in. Later various derivatives were created using the same basic cartridge, but with smaller-diameter bullets; these were named by the cartridge diameter at the base and mouth. The original No. 56 became the .56-56, and the smaller versions, .56-52, .56-50, and .56-46. The .56-52, the most common of the new calibers, used a 50-cal bullet.

Other black powder-era cartridges used naming schemes that appeared similar, but measured entirely different characteristics; .45-70, .44-40, and .32-20 were designated by bullet diameter in hundredths of an inch and standard black powder charge in grains. Optionally, the bullet weight in grains was designated, e.g. .45-70-405.[5] This scheme was far more popular and was carried over after the advent of early smokeless powder cartridges such as the .30-30 Winchester and .22 Long. Later developments used terms to indicate relative power, such as .44 Special and .44 Magnum. Variations on these methods persist today, with new cartridges such as the .204 Ruger and .17 HMR (Hornady Magnum Rimfire).

Metric diameters for small arms refer to cartridge dimensions and are expressed with an "×" between the bore diameter and the length of the cartridge case; for example, the 6.5×55mm Swedish cartridge has a bore diameter of 6.5 mm and a case length of 55 mm.[6]

The means of measuring a rifled bore varies, and may refer to the diameter of the lands or the grooves of the rifling.[7] This is why the .303 British, named for the bird diameter across the lands, actually uses a .311-in bullet (7.70 mm vs. 7.90 mm), as bullet diameter matches the diameter across the grooves.[8] Meanwhile, the .308 Winchester is measured across the grooves and uses a .308-in diameter (7.82-mm) bullet; the military-specification version is known as 7.62×51mm NATO, so called because the bore diameter measured between the lands is 7.62 mm, and the cartridge has a case 51 mm long.[9]

Metric and US customary

The following table lists some commonly used calibers where both metric and US customary are used as equivalents. Due to variations in naming conventions, and the whims of the cartridge manufacturers, bullet diameters can vary widely from the diameter implied by the name. For example, a difference of 0.045 in (1.15 mm) occurs between the smallest and largest of the several cartridges designated as ".38 caliber".

Common calibers in inch and their metric equivalents[10][11][12][13][14]
Inch caliber Metric caliber Typical bullet diameter Common cartridges Notes
.172 4 mm 0.172 in .17 HMR, .17 Hornet, .17 Ackley Hornet, .17 Winchester Super Magnum, .17-32 Magnum, .17 VHA, .17 Remington, .17/222, .17 Mach III-IV, .17 Ackley Improved Bee, .17-357 RG, .17 Remington Fireball, .17 Incinerator, 4.39×39Rmm SPS
.20, .204 5 mm 0.204 in .204 Ruger, 5mm Remington Rimfire Magnum
.221 5.45 mm 0.221 in 5.45×39mm Russian family Russian Mil Std
.22 5.6 mm 0.223 in .22 Short, .22 Long, .22 Long Rifle, .22 Stinger, 22 Extra Long, .297/230 Morris Extra Long, .22 Hornet, .22 Rem Automatic, 5.66 x39 MPS, .22 Rem Jet
.224 5.7 mm 0.224 in .218 Bee, .219 Zipper, .22 Hornet-K, .220 Swift, .222 Remington, .222 Remington Magnum, .223 Remington, 5.56×45mm NATO, 5.7×28mm, .22 TCM, 5.8 × 42 Chinese, .224 Weatherby Magnum, .225 Winchester, .223 Winchester Super Short Magnum (Obsolete) .223 Ackley Improved, .219 Donaldson Wasp, .221 Remington Fireball, .22-250 Remington and many more
.243 6 mm 0.243 in .243 Winchester, .244 Remington, 6mm Remington, 6 mm plastic airsoft BBs, 6mm Whisper, 6mm PPC, 6mm Bench Rest Remington, 6×45mm, 6×47mm, 6mm Cheetah, .240 Weatherby, 6×62 Freres, 6mm Norma BR, 6XC Tubb, 6mm JDJ, 6mm SAW, 6-250 Walker, 6.17 Spitfire, 6.17 Flash, 6mm Lee Navy, and more,
.25 6.35 mm 0.257 in, 6.35 mm .25 ACP (0.251"), 250/3000 Savage, 257 Roberts, 25-06 (0.257"), also called .25 Auto and 6.35mm Browning
.26 6.5 mm 0.264 in, 6.7 mm 6.5×55mm, .260 Remington, 26 Nosler, 6.5 Creedmoor, 6.5x47 Lapua cartridges commonly known as '6.5 mm'
.27 6.8 mm 0.277 in, 7.035 mm .270 Winchester, 6.8 SPC
.284 7 mm 0.284 in, 7.213 mm .280 Remington, 7mm-08 Remington, 7mm Weatherby Magnum, 7mm Remington Magnum, 7×57mm Mauser, 7×64mm commonly called '7 mm'
.308 7.62 mm 0.308 in, 7.82 mm .30 Luger (7.65 × 21mm Luger), .30-30 Win, 30 Herrett, .300 Whisper, .30-378 Weatherby, 7.63 Mannlicher–Schoenauer, 7.63 Mauser, .30 USA Rimless, .308 Corbon, .3-9 Savage, .30 Kurz, 300 AAC Blackout (7.62×35mm), 7.5mm Schmidt–Rubin, .300 Winchester Magnum, .30 Carbine, 309 JDJ, .30-03, .30-06 Springfield, .30-06 JDJ, .307 GNR, .308 Winchester (7.62×51mm NATO), .300 Weatherby Magnum, .30 Army (.30-40 Krag), 7.82mm Lazzeroni, and dozens more
.311 7.9 mm 0.311 in, 7.92 mm .303 British, 7.62×39mm Soviet, 7.62×54mmR, 7.62×25mm, 7.7×58mm 7.62×54mmR is actually 7.92 mm (Mosin, SVD, PKM, etc.) The same applies to 7.62×39mm (AK-47, AKM, etc.)
.312 7.94 mm 0.312 in, 7.94 mm .32 ACP Also known as 7.65 × 17 mm Browning
.323 8 mm 0.323 in, 8.20 mm 8×57mm IS, .325 WSM, 8mm Remington Magnum, 8 mm plastic (airsoft) BBs .32 caliber rifle cartridges
.338 8.6 mm 0.338 in .338 Lapua, .338 Norma Magnum, .338 Winchester Magnum, .338-378 Weatherby Magnum C14 Timberwolf (Canadian Forces)
.355 9 mm 0.355 in 9mm Luger, 9mm Ultra, 9mm Bayard Long, 9mm Browning Long, 9mm Mauser, 9mm Winchester Magnum, 9mm Glisenti, 9 × 21mm, 9 × 23mm Winchester, 9mm Mi-Bullet, 9mm Steyr, .356 Team Smith & Wesson, 9mm Federal, 9mm × 25mm Dillon, 9mm Action Express
.356 9 mm 0.356 in .380 ACP (9mm Short), 9×56mm Mannlicher–Schoenauer, 9mm × 57mm Mauser
.357 9 mm 0.357 in .38 Super, .38 Special, .357 Magnum, .357 SIG, .35 Remington Handgun cartridges known as "38" are .357 caliber. Generally .357 for revolvers and rifles, .355 in autoloaders
.363 9 mm 0.363 in 9×18mm Makarov
.365 9.3 mm 0.365 in 9.3×62mm, 9.3×64mm Brenneke, 9.3×72mmR, 9.3×74mmR
.375 9.5 mm 0.375 in, 9.53 mm .375 H&H Magnum, 9.5×57mm Mannlicher–Schönauer (.375 Rimless Nitro Express (RNE) × 2¼)
.40 10 mm 0.400 in .40 S&W, 10mm Auto
.44 10.9 mm 0.429 in .444 Marlin, .44 S&W Russian, .44 S&W Special, .44 Remington Magnum, .44 Auto Mag, .440 Cor-Bon, .44/454 JDJ Woodswalker
.45 11.43 mm 0.451–0.454 in .45 ACP, .45 GAP, .454 Casull, .45 Long Colt, .455 Webley Bullet diameter depends on bullet type/material. Generally 0.451 in for full metal jacket bullets and 0.454 in for lead bullets.
.50 12.7 mm 0.510 in, 12.95 mm .50 BMG, .50 Action Express, 12.7×108mm, .500 S&W Magnum M2 Browning machine gun and other heavy machine guns, long-range rifles typified by Barrett products. Desert Eagle handgun.

Shotguns

Main page: Gauge (firearms)

Shotguns are classed according to gauge, a related expression. The gauge of a shotgun refers to how many lead spheres, each with a diameter equal to that of the bore, amount to one pound in weight. In the case of a 12-gauge shotgun, it would take 12 spheres the size of the shotgun's bore to equal a pound.[15] A numerically larger gauge indicates a smaller barrel: a 20-gauge shotgun requires more spheres to equal a pound; therefore, its barrel is smaller than the 12-gauge. This metric is used in Russia as "caliber number": e.g., "shotgun of the 12 caliber." The 16th caliber is known as "lordly" (Russian: барский). While shotgun bores can be expressed in calibers (the .410 bore shotgun is in fact a caliber measure of .41 caliber [10.4 mm]),[16] the nature of shotshells is such that the barrel diameter often varies significantly down the length of the shotgun barrel, with various levels of choke and backboring.

Caliber as measurement of length

The length of artillery barrels has often been described in terms of multiples of the bore diameter e.g. a 4-inch gun of 50 calibers would have a barrel 4 in × 50 = 200 in long. A 50 caliber 16 inch gun (16 inch diameter shell), has a barrel length (muzzle to breech) of 50 × 16 = 800 in (66 ft 8 in). Both 14-in and 16-in navy guns were common in World War II. The British Royal Navy insisted on 50-cal guns on ships as it would allow 1,900 to 2,700 lb (860 to 1,220 kg) shells to travel at an initial velocity of up to 1,800 mph (2,896 km/h) to a distance of 26 mi (42 km).[citation needed]

Pounds as a measure of cannon bore

Smoothbore cannon and carronade bores are designated by the weight in imperial pounds of spherical solid iron shot of diameter to fit the bore. Standard sizes are 6, 12, 18, 24, 32, and 42 pounds, with some 68-pound weapons, and other nonstandard weapons using the same scheme. See Carronade.

From about the middle of the 17th century until the middle of the 19th century, measurement of the bore of large gunpowder weapons was usually expressed as the weight of its iron shot in pounds. Iron shot was used as the standard reference because iron was the most common material used for artillery ammunition during that period, and solid spherical shot the most common form encountered. Artillery was classified thereby into standard categories, with 3-pounders (pdr.), 4-pdr., 6-pdr., 8-pdr., 9-pdr., 12-pdr., 18-pdr., 24-pdr., and 32-pdr. being the most common sizes encountered, although larger, smaller and intermediate sizes existed.

In practice, though, significant variation occurred in the actual mass of the projectile for a given nominal shot weight. The country of manufacture is a significant consideration when determining bore diameters. For example, the French livre, until 1812, had a mass of 489.5 g whilst the contemporary English (avoirdupois) pound massed approximately 454 g. Thus, a French 32-pdr. at the Battle of Trafalgar threw a shot with 1.138 kg more mass than an English 32-pdr.

Complicating matters further, muzzle-loaded weapons require a significant gap between the sides of the tube bore and the surface of the shot. This is necessary so the projectile may be inserted from the mouth to the base of the tube and seated securely adjacent the propellant charge with relative ease. The gap, called windage, increases the size of the bore with respect to the diameter of the shot somewhere between 10% and 20% depending upon the year the tube was cast and the foundry responsible.

English gun classes c. 1800[citation needed]
gun class (pdr.) shot diameter (cm) shot volume (cm3) approx. service bore (cm) mass of projectile (kg)
2 6.04 172.76 6.64 0.90846
3 6.91 172.76 7.60 1.36028
4 7.60 230.30 8.37 1.81339
6 8.71 345.39 9.58 2.71957
9 10.00 518.28 11.00 4.08091
12 10.97 691.22 12.07 5.44269
18 12.56 1036.96 13.81 8.16499
24 13.82 1382.65 15.20 10.88696
32 15.21 1843.50 16.73 14.51572
64 19.17 3686.90 21.08 29.03063

The relationship between bore diameter and projectile weight was severed following the widespread adoption of rifled weapons during the latter part of the 19th century. Guns continued to be classed by projectile weight into the mid-20th century, particularly in British service. However, this value no longer definitively related to bore diameter, since projectiles were no longer simple spheres—and in any case were more often hollow shells filled with explosives rather than solid iron shot.

See also

References

Barnes, Frank C. (2016). Woodard, W. Todd. ed. Cartridges of the world : a complete and illustrated reference for more than 1500 cartridges (15th ed.). Krause Publications. ISBN 1440246424. OCLC 934886116. 

  1. Brown, Edmund G. (2009). Handgun Safety Certificate. West Sacramento, California: California Department of Justice. p. 52. 
  2. Barnes, Cartridges of the World 15 Edition 2016, p. 9.
  3. Frank C. Barnes. Stan Skinner. ed. Cartridges of the World (10th ed.). Krause Publications. ISBN 0-87349-605-1. 
  4. Barnes, Frank C. (1997) [1965]. McPherson, M.L.. ed. Cartridges of the World (8th ed.). DBI Books. pp. 8–12. ISBN 0-87349-178-5. 
  5. Barnes, Cartridges of the World 15 Edition 2016, p. 9.
  6. Barnes, Cartridges of the World 15 Edition 2016, p. 9.
  7. Barnes, Cartridges of the World 15 Edition 2016, p. 9.
  8. Barnes, Cartridges of the World 15 Edition 2016, p. 504.
  9. Barnes, Cartridges of the World 15 Edition 2016, p. 670.
  10. Accurate (2000). Accurate Smokeless Powders Loading Guide (Number Two (Revised) ed.). Prescott, AZ: Wolfe Publishing. p. 392. barcode 94794 00200. 
  11. "Pistol and Rifle Lead Bullets". http://www.blue-star-inc.com/catalog/lprbullet.htm. 
  12. "Rifle Bullets". http://www.blue-star-inc.com/catalog/lprbullet.htm. 
  13. "LeadSafe Total Copper Jacket ("TCJ") Bullet List". http://www.rainierballistics.com/mainframe.htm. 
  14. Frank C Barnes. Cartridges of the World (14th ed.). Gun Digest Books. 
  15. Barnes, Cartridges of the World 15 Edition 2016, p. 629.
  16. Barnes, Cartridges of the World 15 Edition 2016, p. 629.

External links